Mixing for Wall Tile Installation

Mixing for Wall Tile Installations

 

Follow the Manufacturers instructions for mixing the materials chosen for the project. In addition to the mixing instructions, Manufacturers will include instructions concerning application and estimated coverage. It is the selection of the proper application tools that lead us to a successful job.

 

By following the Manufacturers instructions, we are able to successfully mix bond coat mortars and grouts. Then what do we do with them?

 

Wall Layout

A5h11

Before the bond coat application, walls have a special consideration due gravity. Unsupported tile set on bonding mortar can and will sag. This can be eliminated with the use of a ledger below the first row of tile. If the wall tile starts at floor level, above a shower or tub, or on a counter top the use of a ledger is not necessary. However, care must be taken to insure that the first row of tile is level and flat so those successive rows will remain level and flat.

 

A5h12

A ledger can be a metal or wood straight edge applied to the wall directly below the lower working lines. In three wall tub or shower enclosures, the back wall and sidewalls can have ledgers applied to the three lower working lines. This allows the installer to tile all vertical surfaces and have the grout joints line up perfectly through all three walls.

 

The ledgers can be held in place by temporarily screwing them to the substrate or balancing them on stacked tile. The installer only needs to be careful to make sure the ledger is aligned with the working lines.

Bond Coat

The bond coat must be applied to produce a minimum coverage for the item to be bonded. It is recommended that tile, when set and beat in, has coverage of mortar on the back of the tile greater that 80% in dry interior areas and 95% in wet or exterior areas. It is also recommended that the bond coat be at least 3/32″ thick between the tile and setting bed. That is verified by systematically pulling up several tiles in a field of tile while the installation is in progress.

 

This is the reason you will see various sizes of notched trowels recommended for certain sizes of tile. If the trowel size is not sufficient to provide the coverage, a larger trowel size needs to be selected. If 100% coverage is desired, tiles need to be back-buttered. Back buttering is a good practice especially if the tile has a lug back or is an out of plane shape.

 

Back buttering is not difficult. The process is designed to even out the back of the tile prior to setting the tile and beating it in. For some tiles, this may mean only a thin “skim coat” of the bonding mortar is applied using a straight non-notched finish trowel. Other out of plane tiles may require a thicker coat. The idea, again, is to even out the back of the tile prior to setting.

 

Tile Doctor Tip: For tile larger than 8″ a 1/4″ x 1/4″ notched trowel and back buttering normally leads to 100% coverage. It is best to take the time to use this procedure and eliminate the problems associated with lack of coverage.

 

Is it possible to apply “thin set” mortars too thick? Yes it is. Portland cement “thin set” mortars cure by hydration. While they cure a certain amount of shrinkage will occur. Their bonding strength, if applied too thick, can actually fracture tile. This is the reason you will see “medium set” mortars available. Medium set mortar is manufactured for specific installation requirements. It is especially useful when setting tile on irregular setting beds and tile that varies in thickness.

 

The procedure for applying the setting bed is simple. Without covering or disturbing the layout lines or ledger, a sufficient amount of bonding mortar is applied to the substrate using the flat side of the notched trowel first. Scoop out enough mortar to skim coat the whole surface to receive tile.

 

A5h13

Use the flat side of the trowel to push the mortar firmly into the substrate. Then apply enough mortar to comb out the desired area using the notched side at 45° to a uniform depth. Be careful to come as close to the layout lines as possible without obscuring the lines. This can be accomplished with a little practice.

 

Tile Doctor Tip: Do not comb out an area too large if the area can not be tiled completely within 10-15 minutes. If the mortar skims or the surface dries to any degree, it will not bond the tile.